? TDA2003 10w car radio audio amplifier description the tda 2003 has improved performance with the same pin configuration as the tda 2002. the additional features of tda 2002, very low number of external components, ease of assembly, space and cost saving, are maintained. the device provides a high output current capability (up to 3.5a) very low harmonic and cross-over distortion. completely safe operation is guaranteed due to protection against dc and ac short circuit between all pins and ground, thermal over-range, load dump voltage surge up to 40v and fortuitous open ground. september 2013 symbol parameter value unit v s peak supply voltage (50ms) 40 v v s dc supply voltage 28 v v s operating supply voltage 18 v i o output peak current (repetitive) 3.5 a i o output peak current (non repetitive) 4.5 a ptot power dissipation at tcase = 90c 20 w t stg , t j storage and junction temeperature -40 to 150 c absolute maximum ratings test circuit pentawatt ordering numbers : tda 2003h tda 2003v 1/10
symbol parameter value unit r th-j-case thermal resistance junction-case max 3 c/w thermal data 2/10 pin connection (top view) schematic diagram TDA2003
symbol parameter test conditions min. typ. max. unit dc characteristics (refer to dc test circuit) v s supply voltage 8 18 v v o quiescent output voltage (pin 4) 6.1 6.9 7.7 v i d quiescent drain current (pin 5) 44 50 ma ac characteristics (refer to ac test circuit, gv = 40 db) p o output power d = 10% f = 1 khz r l = 4 w r l = 2 w r l = 3.2 w r l = 1.6 w 5.5 9 6 10 7.5 12 w w w w v i(rms) input saturation voltage 300 mv v i input sensitivity f = 1 khz p o = 0.5w p o = 6w p o = 0.5w p o 10w r l = 4 w r l = 4 w r l = 2 w r l = 2 w 14 55 10 50 mv mv mv mv electrical characteristics ( v s = 14.4v, t amb = 25 c unless otherwise specified) dc test circuit ac test circuit 3/10 TDA2003
4/10 figure 1. quiescent output voltage vs. supply voltage figure 2. quiescent drain current vs. supply voltage figure 3. output power vs. supply voltage symbol parameter test conditions min. typ. max. unit b frequency response (-3 db) p o = 1w r l = 4 w 40 to 15,000 hz d distortion f = 1 khz p o = 0.05 to4.5w r l = 4 w p o = 0.05 to 7.5w r l = 2 w 0.15 0.15 % % r i input resistance (pin 1) f = 1 khz 70 150 k w g v voltage gain (open loop) f = 1 khz f = 10 khz 80 60 db db g v voltage gain (closed loop) f = 1 khz r l = 4 w 39.3 40 40.3 db e n input noise voltage (0) 1 5 m v i n input noise curre nt (0) 60 200 pa h effici ency f = 1 hz p o = 6w p o = 10w r l = 4 w r l = 2 w 69 65 % % svr supply voltage rejection f = 100 hz v ripple = 0.5v r g = 10 k w r l = 4 w 30 36 db electrical characteristics (continued) (0) filter with noise bandwidth: 22 hz to 22 khz TDA2003
figure 4. output power vs. load resistance r l figure 5. gain vs. input sensivity figure 6. gain vs. input sensivity figure 7. distortion vs. output power figure 8. distortion vs. frequency figure 9. supply voltage rejection vs. voltage gain figure 10. supply voltage rejection vs. frequency figure 11. power dissipa- tion and efficiency vs. output power (r l = 4 w ) figure 12. power dissipa- tion and efficiency vs. output power (r l = 2 w ) 5/10 TDA2003
6/10 figure 13. maximum power dissipation vs. supply voltage (sine wave operation) figure 14. maximum allowable power dissipation vs. ambient temperature figure 15. typical values of capacitor (c x ) for different values of frequency reponse (b) figure 16. typical application circuit figure 17. p.c. board and component layout for the circuit of fig. 16 (1 : 1 scale) application information built-in protection systems load dump voltage surge the tda 2003 has a circuit which enables it to withstand a voltage pulse train, on pin 5, of the type shown in fig. 19. if the supply voltage peaks to more than 40v, then an lc filter must be inserted between the supply and pin 5, in order to assure that the pulses at pin 5 will be held within the limits shown in fig. 18. a suggested lc network is shown in fig. 19. with this network, a train of pulses with amplitude up to 120v and width of 2 ms can be applied at point a. this type of protection is on when the supply voltage (pulsed or dc) exceeds 18v. for this reason the maximum operating supply voltage is 18v. TDA2003
short-circuit (ac and dc conditions) the tda 2003 can withstand a permanent short- circuit on the output for a supply voltage up to 16v. polarity inversion high current (up to 5a) can be handled by the device with no damage for a longer period than the blow-out time of a quick 1a fuse (normally con- nected in series with the supply). this feature is added to avoid destruction if, during fitting to the car, a mistake on the connection of the supply is made. open ground when the radio is in the on condition and the ground is accidentally opened, a standard audio amplifier will be damaged. on the tda 2003 pro- tection diodes are included to avoid any damage. inductive load a protection diode is provided between pin 4 and 5 (see the internal schematic diagram) to allow use of the tda 2003 with inductive loads. in particular, the tda 2003 can drive a coupling transformer for audio modulation. dc voltage the maximum operating dc voltage on the tda 2003 is 18v. however the device can withstand a dc voltage up to 28v with no damage. this could occur during winter if two batteries were series connected to crank the engine. thermal shut-down the presence of a thermal limiting circuit offers the following advantages: 1) an overload on the output (even if it is perma- nent), oran excessive ambient temperature can be easily withstood. 2) the heat-sink can have a smaller factor com- pared with that of a conventional circuit. there is no device damage in the case of ex- cessive junction temperature: all that happens is that p o (and therefore p tot ) and i d are reduced. figure 20. output power and drain current vs. case temperature (r l = 4 w ) figure 21. output power and drain current vs. case temperature (r l = 2 w ) figure 18. figure 19. 7/10 TDA2003
component recommmended value purpose larger than recommended value smaller than recommended value c1 c1 2.2 m f input dc decoupling noise at switch-on, switch-off c2 470 m f ripple rejection degradation of svr c3 0.1 m f supply bypassing danger of oscillation c4 1000 m f output coupling to load higher low frequency cutoff c5 0.1 m f frequency stability danger of oscillation at high frequencies with inductive loads c x @ 1 2 p b r1 upper frequency cutoff lower bandwidth larger bandwidth r1 (g v -1) r2 setting of gain increase of drain current r2 2.2 w setting of gain and svr degradation of svr r3 1 w frequency stability danger of oscillation at high frequencies with inductive loads r x @ 20 r2 upper frequency cutoff poor high frequency attenuation danger of oscillation pratical consideration printed circuit board the layout shown in fig. 17 is recommended. if different layouts are used, the ground points of input 1 and input 2 must be well decoupled from the ground of the output through which a rather high current flows. assembly suggestion no electrical insulation is required between the package and the heat-sink. pin length should be as short as possible. the soldering temperature must not exceed 260 c for 12 seconds. application suggestions the recommended component values are those shown in the application circuits of fig. 16. different values can be used. the following table is intended to aid the car-radio designer. 8/10 TDA2003
pentawatt v dim. mm inch min. typ. max. min. typ. max. a 4.8 0.189 c 1.37 0.054 d 2.4 2.8 0.094 0.110 d1 1.2 1.35 0.047 0.053 e 0.35 0.55 0.014 0.022 e1 0.76 1.19 0.030 0.047 f 0.8 1.05 0.031 0.041 f1 1 1.4 0.039 0.055 g 3.2 3.4 3.6 0.126 0.134 0.142 g1 6.6 6.8 7 0.260 0.268 0.276 h2 10.4 0.409 h3 10.05 10.4 0.396 0.409 l 17.55 17.85 18.15 0.691 0.703 0.715 l1 15.55 15.75 15.95 0.612 0.620 0.628 l2 21.2 21.4 21.6 0.831 0.843 0.850 l3 22.3 22.5 22.7 0.878 0.886 0.894 l4 1.29 0.051 l5 2.6 3 0.102 0.118 l6 15.1 15.8 0.594 0.622 l7 6 6.6 0.236 0.260 l9 0.2 0.008 m 4.23 4.5 4.75 0.167 0.177 0.187 m1 3.75 4 4.25 0.148 0.157 0.167 v4 40? (typ.) l l1 a c l5 d1 l2 l3 e m1 m d h3 dia. l7 l6 f1 h2 f gg1 e1 f e l9 v4 r r r resin between leads h1 v3 h2 l8 vv v1 b vv v4 v4 outline and mechanical data 9/10 TDA2003
docid1449 rev 3 10/10 TDA2003 10 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems wi th product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2013 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com
|
